Amsoil Synthetic Motor Oil
 

Synthetic Multi-Purpose Grease, NLGI #0 (GLA)

Buy Now/Pricing Information

Package sizes include:

red arrow 35-lb. Lug
red arrow 120-lb. Keg
red arrow 400-lb. Drum
red arrow (no cartridge sizes available for grade NLGI #0)


PRODUCT DESCRIPTION
AMSOIL Synthetic Multi-Purpose Greases are qualified against the highest grease standards and are designed for multiple use applications. Composed of premium quality synthetic base oils and lithium complex thickeners, Multi-Purpose Greases provide superior film strength, shear resistance, adhesion properties and mechanical stability, and they excel in temperature extremes by providing excellent oxidation stability, high temperature dropping points and low temperature torque values and pumping capabilities. AMSOIL Synthetic Multi-Purpose Greases are formulated with oil soluble extreme-pressure additives for heavy loads, as well as oxidation and corrosion inhibitors that impart good oxidation stability and rust protection.

PERFORMANCE FEATURES

  • High dropping point of 430°F
  • Resists thermal and oxidation degradation
  • Excellent water-washout resistance
  • Good low temperature pumpability and torque values
  • Adhesive and shear stable to prevent squeeze out

Applications or Requirements

  • GLA (#0) Cincinnati Milicron P-79 Spec

APPLICATION RECOMMENDATION
AMSOIL Synthetic Multi-Purpose Grease grade #0 is recommended in manual or automatic lubricating systems. NLGI #0 (GLA) has better mobility and is the preferred choice for colder applications, automatic lubrication systems with long pumping runs and gear box applications (where recommended by manufacturer).

The correct consistency grade of AMSOIL Synthetic Multi-Purpose Grease is recommended in heavy and light duty applications found in manufacturing plants, automobiles, agricultural and construction equipment. These include, but are not limited to, roller bearings, plain bearings, thrust bearings, gears, electric motors, presses, winches, bushings, wheel bearings, chassis lubrication, universal joints, ball joints, tie-rod ends, and steering knuckles. AMSOIL Synthetic Multi-Purpose Greases are suitable for use up to 350 degrees F. When operating at elevated temperatures, frequent regreasing may be required.

AMSOIL Synthetic Multi-Purpose Greases are compatible with many other types of greases. However, it is recommended that when changing greases, the equipment be cleaned of the old grease when possible or flushed with a liberal amount of Multi-Purpose Grease while the mechanism is in operation. Closely monitor the system for any inconsistencies. Grease compatibility questions should be referred to your AMSOIL representative or AMSOIL Inc.

APPLICATION MAINTENANCE
Maintaining a clean work environment is important when equipment greasing is performed. Wipe grease fittings clean prior to injecting grease to prevent contaminant ingestion. Maintain bearing housings one-third to one-half full of grease. Do not over-grease, as excessive heat buildup can result. Supplement standard grease maintenance by periodically cleaning and packing housings with fresh grease on an established maintenance schedule.

Buy Now/Pricing Information

Typical Technical Properties
Synthetic GLA Grease GLA
Thickener lithium complex
NLGI consistency grade 0
NLGI performance grade NA
Penetration - ASTM D 217 (25°C [77°F], 0.1 mm) worked 60 strokes 355-385
Dropping point, °F[°C] - ASTM D2265 430 [221]
High temperature life, hours - ASTM D 3527 120
Oxidation stability, psi - ASTM D 942 (100 hr/300 hr) 1/5
Water washout, percent - ASTM D 1264 16.7
Rust and corrosion - ASTM D 1743 pass
Oil separation, percent loss - ASTM D 1742 (24 hours, 25°C [77°F] 5.2
Leakage, g lost - ASTM D 4290 NA
Four ball wear test, mm scar - ASTM D 2266 0.45
Fretting wear, mg - ASTM D 4170 NA
Four ball EP, kgf - ASTM D 2596
Weld point
Load wear index

315
47

Timken OK load test, lbs - ASTM D 2509 45
Low temperature torque, N*m - ASTM D 4693 (-40°C [-40°F]) 0.46
LT-37 pumpability, g/min (60°F/0°F [16°C/-18°C]) 1475/73
Copper corrosion - ASTM D 4048 1B
Disc brake wheel bearing specifications
Ford ESA-M1C 198-A
Chrysler MS-3701
NA
NA
Oil viscosity:
40°C [104°F], cSt
100°C [212°F], cSt

151
19.2

Flash point, °F[°C] - ASTM 92 450[232]
Color red
Texture smooth with tack

NA: Not applicable

Can't find what you're looking for? Pick an option below: 

Amsoil Product Information Request Form
General Questions and Technical Help
Commercial Account Application (For use in personal or Company Equipment)
Retail Account Application Form (Own a store or quick lube shop, etc.)
Amsoil Home Dealership Application Form
Amsoil Preferred Customer Application Form

Synthetic Oil Tech

Amsoil VTwin HD

Amsoil Racing

Synthetic Motor Oil

Other Motor Products

Wix Filters

Mann Filters

Donaldson Endurance

Donaldson Pseries

Request Catalog

Amsoil Factory Direct Online Retail Catalog

Wholesale Catalog
Request Form

Receive Confidential
Wholesale Prices!!!

You will receive no unsolicted email from us! Your privacy is our mission.

Privacy Policy

Amsoil Dealer
John Cardell
Las Vegas NV
702-472-9618

Google