Synthetic PC Series Compressor Oil (ISO 46, SAE 20)
The correct manufacturer-recommended
viscosity grade of AMSOIL PC Series compressor oil is recommended for use in rotary screw, rotary vane,
reciprocating and other compressor applications. Compatible with PAO-, ester- and petroleum-based compressor
oils. They are not compatible with glycol- or silicone-based compressor oils. Consult AMSOIL for further information.
Package sizes include:
1-Quart Bottles (case of 12)
Compressor Oil Cross
Reference Guide (68k PDF)
AMSOIL PC Series Synthetic Compressor Oils are long-life, premium compressor lubricants based on novel, proprietary
technology. They incorporate the highest quality, thermally-stable PAO synthetics fortified with premium
non-detergent, ashless additives for maximum protection at high temperatures and pressures. They last up to eight
times longer than petroleum oils, effectively reducing maintenance and waste oil disposal costs.
Improves Compressor Efficiency
AMSOIL PC Synthetic Compressor Oils have low friction properties and they resist viscosity increase from oxidation.
They help improve operating efficiency and save money on electrical energy consumption.
Controls Foam and Reduces Wear
AMSOIL PC Compressor Oils contain anti-foam additives and, unlike other compressor oils, they are anti-wear
fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for
increased compressor life and efficiency.
Resists Water Contamination
Water from condensation builds up in compressors that can cause unwanted oil/water emulsions, environmental
discharge hazards and rust. AMSOIL PC Synthetic Compressor Oils are hydrolytically stable. They resist acid
formation, readily separate from water and are anti-rust fortified. Water can be easily drained off for simplified
environmental discharge and increased oil life.
Resists Heat and Oxidation
AMSOIL PC Series Compressor Oils combine the inherent stability of premium synthetic base oils with specialized
anti-oxidant additives to resist varnish, carbon and acid formation. They protect compressors better and last
longer in service than petroleum oils, especially during hot operating conditions.
AMSOIL PC Series Synthetic Compressor Oils are ashless, high flash point formulations with very low carbonforming
tendencies that minimize the incidence of ignition-promoting “hot spots.” While PC Synthetic Compressor Oils can
provide improved fire safety, they cannot be considered non-flammable.
The appropriate viscosity of AMSOIL PC Series Synthetic Compressor Oil is recommended for use in single and
multistage rotary screw, vane, centrifugal and reciprocating compressor crankcase and cylinders, vacuum pumps and
other applications such as gears, bearings, blowers, pumps and handheld pneumatic tools. In compressor
applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are
subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best
performance, AMSOIL recommends the compressor be drained prior to the installation of PC Synthetic Compressor Oil.
If carbon deposits are present on the internal components, it is recommended they be removed following the
compressor manufacturer recommendations.
|• Nitrogen • Hydrogen • Helium • Carbon Monoxide
• Carbon Dioxide (dry) • Ethylene • Methane • Propane
• Butane • Propylene • Butylenes • Natural Gas
• Benzene • Butadiene • Furnace (crack gas)
• Hydrogen Sulfide (dry) • Synthetic Gas
• Sulfur Dioxide.
|• Epoxy • Oil Resistant Alkyd • Acrylic Enamel.
|• Acetal (Delrin) • ABS • Phenolic • Polyamide-imide
• Polyamide (Nylon)
• Polycarbonate (metal covered only)
• Polyester • Polyetherimide (Nylon) • Polyimide
• Polyphenylene oxide • Polystyrene • Polysulfone
• PTFE (Teflon) • Terephthalate.
|• Fluoroelastomer (Viton) • Nitrile (Buna N) • Polyacrylate
• TFE/P • Poly Urethane.
|Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended
for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl,
ethylene-propylene or SBR rubber. PC Series Oils are Not Compatible with polyalkylene glycol or
HEALTH & SAFETY
This product is not expected to cause health concerns when used for the intended application and according to the
recommendations in the Material Safety Data Sheet (MSDS). An MSDS is available upon request at 715-392-7101 or
on the AMSOIL Website. Keep Out of Reach of Children. Don't pollute. Return
used oil to collection centers.
Typical Technical Properties
|Synthetic PC Series Compressor
|ISO VG - ASTM D-2422
|VK 100°C - ASTM D-445
|VK 40°C - ASTM D-445
|Viscosity Index - ASTM D-2270
|SPGR - ASTM D-1298
|Density - ASTM D-1298
|Flash Point °C (°F) - ASTM D-92
|Fire Point °C (°F) - ASTM D-92
|Pour Point °C (°F) - ASTM D-97
|Four-Ball Wear Test - ASTM D-4172 (40 kg, 1200
rpm, 75° C, 60 min.)
|Copper Strip Corrosion Test - ASTM
|Rust Test - ASTM D665 A & B Fresh Water and
Synthetic Sea Water
|Foam, ml (ASTM D-892) Sequence I, II, III Test End
- and After 10 minutes settling
|Demulsibility ASTM D-1401 [oil/water/cuff
Can't find what you're looking for? Pick an option below: